• Pulverisers
• Poultry Machinery
• Wet Grinders
• Potato Wafer Machinery
• Papad Making Machines
• Chip Cutting Machines
• Domestic Flour Mills
• Papad Rolling Machines
 

Domestic Flour Mill
 
Domestic Flour Mill
Sennd Your Request
 
General Number Setting
1-3 Bajra 1-4 Wheat 3-5 maize
4-6 Rice 7-12 All type of Dals 5-10 Spices
10-15 Bafla - bati 15-23 Kill rava 23-28 Extra Coarse
 
 
Through Cleaning :-
•

Unlock the Checknut Ring (Turn Anti Clock wise) and then rotate the Pointer (Pressure Plant with Upper Stone in side) till the Pressure Plate comes out.
•

Clean the inside Grinding Chamber with the help of Wire Brush and Tooth Brush. Also clean the threads of pressure plate and chamber Ring.
•

Don't forget to keep the S.S. Wave Washer on the Chamber and then fLX the Pressure plate.
•

First turn the pressure plate anticlock wise and then rotate clockwise so that the threads are properly matched.
•

Rotate the Pressure Plate till both the Stones Touch (ensure that checknut ring is free) and then adjust the Pointer to required grinding positing positting. Now lock the Checknut Ring by rotating it Clockwise.
   
  Important :-
•

The Pin should be plugged out while Thorough Cleaning.
•
See the Checknut Ring is free while rotating the pressure plate.
•
Never run the Flour Mill behind 1 No. (Where both Stones Touch)
•
To clean the burnt Flour (due to Moist Grain, Dal etc.) Stuck on the stone. Simply grind 200 gms. of wheat between 23/28 no.
   
 
Common Problem & Remedies :-
 
Tripping Problem, Motor starts and stops every few minutes. whole or Partly Grinded Grains, Instead of fours. Motor not running and making humming noise.
 
Tripping Problem, is caused due to any of the following reasons.
 
(a) Chamber is overloaded or choked.
(b) Voltage is very low or high.
(c) Pointer is on zero number where both the stones are locked.
(d) The grinding item is moist.
 
Whole or partly Grinded Grains instead offlours is because the pointer is one or more thread open.
  For any time of the above problems follow the following steps.
 
1)
 Empty the hopper and container.
2)
 Clean the Chamber from outlet till pressured Air is Free Flowing.
3)
Set the point on zero where both the stones are locked and then adjust the pointer to any required grinding position, other the zero. Ensure that checknut ring is free while adjusting the number.
4)
First grind only a small quantity and check for the fineness and proper working of the machine. If you are satisfied then grind your required quantity.
  If the Grinding Item is moist it will stick on the stones. Which results to tripping problem. The best way to clean the stones is to grind 200 gms. of wheat on any coare number between 23 to 28.

Motor not running and making huming Sound, this complain is very rare and is due to clutch setting. Switch off the machine and tap the allum. Cap on the Lower stone with wodden tapper. Now switch on the machine and motor will start.

Jtill if any problems persist than contact your nearest dealer or us for prompt service.
   
 
Precautions :-
 
Before using RlDHI SIDHI take thefollowingprecautions:
•
Do not run it on low voltage other-wise the motor will stop functioning
•
Do not bring the stones too close while adjusting. This results into overloading. Motor will stop functioning.
•
Do not grind moist grains. Dry chana dal in the sun or heat it in the vessel before grinding in case if machine stops functioning while grinding chana dal, grind 200 gms. of wheat first and than grind chana dal, machine willfunction smoothly.
•
 Stones should be cleaned with brush not will water.
•
Lock the checknut every time after adjusting the pointer.
Before using RlDHI-SIDHI after a long interval of time, first grind only 100 gms. of grains.
 
Check List
Rexine Cover for Flourmill.
Rexine Cover for Fitter Set.
Wooden Tapper. (For Dusting)
Rubber outlet Cover.
Tooth Brush. (For Cleaning Threads)
Bottle Brush.(For Cleaning Chamber)
Hopper Knob (3)
Napkeen.
 
1 yrs. Warranty On Machine & 1 yrs. Warranty on Motor against burning
 
WARRANTY is given against all manufacturing defects (except ball bearings. capacitor, overtoad protector and fully automatic device) for a period of two years from the date of delivery. and will be rectified free of charge provided the same is senUo our factory. freight paid.

The WARRANTY however, does not include fault of damage resulting from faulty use of defective starter and switches.

 
  AUTOMATIC MODEL
1.
Automatic model has additional feature which will run the motor only when we fill the hopper (minimum 100 gms.) to grind and on completion of grinding it will stop the motor after few minutes (few minutes required to clean the chamber).
2.
The Automatic pin has to be plugged in on the pressure plate for automatic function to work.
3.
While cleaning when the motor has to be runned empty remove the / automatic pin from the pressure plate. In case of malfunction in Automatic system, by removing the pin prinding is possible.
4.
Automatic model has a LED light indicator for number setting which is more easy and convenient than pointer. Plug in the automatic pin on pressure plate and switch on the machine to make LED light glow.
Top
 
 
 
 
Designed by : MID  Hosted by : PBD  Promoted by : GID